How to Replace a kia key fob replacement cost Sportage Replacement Key

The key of many Kia models comes with the keyless entry feature built in. This key is similar to remote controls and is exchangeable by a Kia dealer.

Key fobs can fail to function due to a number of reasons, such as the battery being dead, worn-out buttons signal interference or water damage. Here are some tips to assist you in getting your Kia key fob that is a replacement car key kia for the sportage again.

How do you replace a smartkey or remote key?

It doesn't matter if your Kia comes with an intelligent key, remote key, push-to-start key, or regular metal non-transponder key The battery inside these keys will eventually require replacing. This is especially when the vehicle displays a message that indicates that the smart key or remote has a low battery.

Luckily, it's a relatively simple process. To replace the keyfob battery remove your mechanical key from the slot at the back of the fob. Then, pull the cover open. Inside the key fob, there will be an incredibly small screw that holds the battery in place. Utilizing a small screwdriver loosen the screw and pull out the old battery. Insert the new battery and then close the slit on the key fob.

Test the key fob by pressing the lock and unlock buttons. If the doors unlock and lock exactly as you expect, then you're all set! You can now utilize your kia sportage spare key's hands-free lock/unlock feature whenever your fingers feel cold or you need to go on errands around Brandon.

Note: Certain key fobs (transponder chip or smart keys) may require their programming completed. This requires a particular programming machine that only the dealer or locksmith can access. Other keys (non transponder keys made of steel) are not required for programming. If you're looking to reprogramme your key, you'll need to note the key code's number on the tag for the key code.

How do you replace a battery?

If your Kia Smart Key replacement key fob is not responding to pressing the lock or unlock button on the fob, this is a sign that the battery needs to be replaced. A low battery can also cause other issues, like the check engine light flashing or the engine not working properly. Fortunately replacing the battery on the key fob is a relatively easy DIY project that requires just a few tools.

Before beginning the process before beginning the process, ensure that your vehicle is off and that all doors are closed. Find the small, metal or plastic piece at the bottom of your key fob, and jiggle it until a metal key slips out. You can then insert the key into the handle on the door of your driver to open your car.

To replace the battery inside the key fob, you must remove the cover that covers the rear. Make use of a plastic pry tool to remove the latch that holds the black negative cable. Remove the old battery and then align the replacement battery so that its "+" side faces you, and the "-" negative side is facing the fob's electrical contacts. Avoid using too much force when pushing the new CR2032 into position to avoid damaging or bending the metal contacts.

After you have installed the new battery, turn the key fob on and off in the ignition until the door locks cycle. You can then test your Kia's keys fob to ensure it's working as intended.

How do I replace a smart keys

You may have either the standard keyfob or Smart Key based upon the model of Kia Sportage. The smart key has an embedded mechanical key blade, however, the standard key fob does not. Both kinds of key fobs come with an internal battery that will eventually have to be replaced. It's quite simple and takes just two minutes.

Make sure to shut off your Kia, and be on a level, well-lit surface before you begin. Be aware that there are tiny components inside the fob which could be snagged if not careful.

The first step is to find the small release button that is located on the back of the lower part of the fob. It could be an oval silver button or a rectangular slot. You can open the key fob by pressing the button.

Once the key fob is opened, remove the old battery. The new battery should be a CR-2032, and can be purchased online or at your local auto parts store. After installation you should be able to lock and unlock your vehicle with your key fob, even if your engine isn't running!

How do you replace a broken mechanical key

The Kia key fob is an amazing option that lets us lock and unlock our vehicle with the click of the button. But, as with all devices it may have issues at times. There are ways to resolve these issues and keep our key fobs in good working order over the long haul.

One of the most common problems is a weak or dead battery. The battery could cause the device to stop working or operate intermittently. If this is the case, try replacing the battery with a new one.

If this doesn't solve the issue, you can use a standard flathead screwdriver to wedge the fob's plastic casing open. Be careful not to harm any internal components or scratch the plastic. Once open, carefully remove the old battery and replace it with a brand new one.

Close and open the door using the mechanical key. (Every Kia fob comes with a spare mechanical key which will fit into the slot). Test the key fob to make sure it is working properly. If the device not working, contact a locksmith or dealer to help resolve the problem. To avoid a lockout in the future ensure that you have an emergency key that will be able to work with all door and trunk cylinders.