Reasons Your fiat panda Key fob replacement 500 Key Fob Won't Work

A key fob with the fiat 500 remote key replacement 500 number is a great way to open the doors and start the car. However, there are a variety of reasons why the key fob might stop functioning. This could be due to a dead coin battery, damaged receiver module, water damage issues, and interfering.

This listing is for an NEW replacement fiat 500 key programming Flip fiat ducato key programming Remote that appears similar to the Ilco brand. It needs to be professionally programmed (click here to find local locksmiths for your vehicle). Includes lock, unlock and trunk buttons.

Dead Coin Battery

The most common reason your 500 key fob will not work is the battery is dead. Modern key fobs have limited operating range and must be within only a few inches from the vehicle to work. If you're far away from your vehicle and press the key fob button, the car will not respond, and will display the "Key Fob Not Detected" message in the instrument cluster.

If this happens then replace the battery for your coin-cell (Part Number CR2032) by a fresh one of a reputable brand like Panasonic Duracell or Energizer. You can typically find them at your local hardware store, or online.

After you've replaced the battery in the coin cell you can test it by standing next to your fiat remote key 500 and pressing the buttons. The parking lights should flash and the key fob should operate the lock and unlock switches.

If the key fob won't function after replacing the battery, it may have water damage that stops it from communicating with the receiver module inside your car. Water damage can happen in many ways, such as a simple splash or submerging the key fob into saltwater at the beach. If you suspect that your fob has been exposed to water, try putting it in a dry rice bag to pull the moisture out. If that doesn't work, your fob may require reprogramming by a professional auto locksmith or the dealer.

Water Damage

The fob does have rubber seals that keep water out of the chip's electronic circuit, submerging it in the ocean or washing it in a machine could cause water damage. Saltwater is especially dangerous to the circuit board of the fob which causes it to short out and eventually end up dying. It's not good to soak the fob in water however, don't give it up when you accidentally drop it in the water or don't take it out of your pants pocket.

Take the battery off first. Before replacing the battery clean the electronic chip using isopropyl or another similar product. Then check the fob to test if it works. If the key does not function, it may need to be changed. This is usually handled by an auto locksmith or dealer.

If the key you have is older and not programmed to work with your vehicle You will need to replace it completely. This is an easy process that can be handled by a professional automotive locksmith. The locksmith needs to cut the key to match the ignition of your car. They will also need to program the fob into the car's system. This is a cost-effective and quick process that can be completed in the same day.

Receiver Module Issues

One of the most common reasons why your 500 key fob may stop functioning is because it's out of range. The remote usually has an operating range of 30 feet or less, and if it's too far from your vehicle, it will not respond to your commands. It can be solved by moving it closer to your vehicle until it begins responding.

If you've replaced the coin battery (commonly called"button" or "button" or "watch") and your fob still won't work, it could have an internal circuit board problem. Reprogramming the fob is usually the solution to this issue. You can find directions on how to get fiat key code to do this for most automobiles by searching YouTube or reading the owner's manual.

It's possible that you need to replace the metal retaining clips that hold the coin battery in place. If they loose tension they could stop the battery from sitting properly and cause your remote to malfunction.

In rare cases the fob could be disconnected from your vehicle due to software issues or hardware issues. This could cause a significant headache, but you can often fix this by visiting an auto locksmith to have them reprogram your fob. In some cases they may have to reinstall the software in your body control module, as well.

Interference

In addition to a dead battery on a coin the key fob could not be able to receive or transmit signals due to interference. This could occur if the key fob is near radio transmitters (cell phones or radar detectors) or another source of electromagnetic radiation. The key fob may not work due to a poor connection to the buttons water damage or damage to the internal chips.

If your key fob suddenly stopped working, or if you've tried everything at home to resolve it (e.g. You might have a damaged 500 receiver module in the event that you've tried replacing the battery, reprogramming it, or using a spare key fob. The receiver module is located under the dash and is able to pick up the radio frequency signals from the key fob. It converts them to electronic commands that the vehicle interprets.

There's a simple method to reset the 500's internal system including the keyfob. Disconnect the 12 volt battery for approximately 15 minutes by removing the negative cable first then the positive cable. Reconnect the battery. This will eliminate any residual electricity and restart the car's computer system, which could help get your key fob working again. If the issue persists, you should seek out an expert technician. They'll be able determine the exact cause of your issues.